Product Description
- The maximum production width of the corrugated cardboard:1400-2500mm
- Design speed:150m/min
- Economic speed:80-1000m/min
- Flute-type combination:A ,C, B, E(as customers' requirement)
- Steam the necessary requirements:
amount of steam 2500-3000Kg/Hr
the highest pressure:1.2MPa
common pressure:0.8-1.1MPa
6.power supply:380V 50Hz Three-phase four-wire system
7.equipment installed total power:about150Kw The actual power consumption:about 80Kw(full speed)
8.equipment covers:about 60m×10m×5m (Specific length of foundation Figure prevail)
9.Equipment out of paper orientation:According to the user to determine the transmission plant set left or right position
10.Equipment applicability,Available in A, B, C class domestic or imported paper Paper
Detailed Photos
1,Backstands action mode:mechanical electric operation
2,the range of paper jams:maximum:1800mm minimum:600mm
3,the diameter of paper jams:maximum:¢1400mm minimum:¢400mm
4,Unilateral maximum load:maximum2000Kg
5,Powered motor parameters:
Paper jams motor550W×4set 380V 50HZ short(S2)working standard
lift motor 1.5Kw 380V 50HZ short(S2)working standard
★Adopt vacuum suction structure, with high pressure strong blower.Suction with silencer.Gas supply and electrical control cabinet to focus on the same operation cabinet,not less than 1.5 meters away from the host,Fully enclosed full operation side.
★base and wallboard cast iron wall,Wallboard thickness130mm.universal Joints.
★corrugated roller material adopt 48CrMoalloy steel,quenched,Laser hardening,Surface finish,main roll of corrugated diameter¢ 280mm,surface hardnessHRC60degree above.The key parts of the tile and pressure roller bearings Wafangdian produce high temperature bearings.
★pressure roller ¢ 284mm,surface grinding and chrome-plated;cylinder control and remove up and down, 45 carbon steel materials, quenching (with cushioning devices).
★pneumatic control glue to glue back, glue roller diameter ¢215mm,Engraved polished surface after a 36-line pit style textured machined chrome plated,after scraping the roller surface polished hard chrome plated.
★Corrugated roller, pressure roller materials provided by the Central Plains Steel,High on corrugating unilateral 0.15mm, 0.075mm high pressure roller unilateral. Plus stopper. ¢ 160mm cylinder with compression cylinder.
★preheat roll adopt seamless steel pipe production by tiangang ¢ 300mm,connecting with metal Hose.
★In accordance with national standard category pressure vessel,and with the pressure vessel certificate.
★The roll surface after precision grinding, fine grinding and hard chromium plating processing,surface friction,durable.
★electric adjustable angle, angle can rotate in the range of 360°,and adjust the paper preheat area.
★Heating plate surface by grinding treatment, hot plate width 600mm, a total of 12 heating plate and cooling 4 m.
Heating plate with a container board production, in line with national standards for a class pressure vessel, with pressure vessel certificate and inspection certificate.
★Hot plate with intensive gravitational roll structure. Roll adopt pneumatic lifting.
★Heating plate heat transfer pipe temperature control sub-four-segment, with a temperature display.
★on cotton use two-cylinder S type cotton belt with the tensioning device.
★lower belt adopt pneumatic tensioning.
★Drive roller coated with attached wear-resistant rubber ,showed a herringbone structure,With a high, ensure smooth cardboard output.
★Main drive motor for frequency conversion motor,low-speed torque,wide speed range ,reliable, and easy maintenance.
★hot plate internal for partition isolation structure,s-shaped flow of steam,Steam, water separation function significantly improves the utilization of steam.
★Overcome the conventional type of pole, cutting pressure lines appear when collapsed cardboard cut phenomenon, cutting board smooth, quality has improved significantly.
★the whole machine can remove left and right,cycloid reducer to adjust.
★Cutter and easy to adjust the pressure line, the error ± 0.5mm, automatic sharpening device, you can achieve timing Brothers, with intermittent Brothers and other features.
★the machine adopt five knives eight lines,the blade is made of tungsten alloy steel, the using life is not less than 3 million running meters.
FAQ
FAQ
1.Q: What is your minimum order quantity, can you send me samples?
A: Our mininun quantity is 1 set, as our product is machinery equipment, it difficult to send you samples, if you have any questions about the products, please feel free to contact us for more detail, we are glad to provide you more information such as specifications,video, etc
3.Q: How does your factory do regarding quality controlling?
A: 1)All raw material we used are environmental-friendly.
2)Skillful workers care every details in handling the producing and packing process.
3) Quality control department are specially responsible for quality in each process.
3.Q: How about the after-sale service?
A: 1)TM online for 24 hours, also contact by email, skype, MSN, whatsapp, etc.
2)To solve the problems with videos/pictures.
3)One year warranty for spare parts change.
Audited Supplier 
){kind=link}